Master Throttle Response on Your 25 kW E Ride Pro SR

Why Tuning Your E Ride Pro SR Matters

The E Ride Pro SR is an impressive 25 kW electric dirt bike, but its throttle can be overly sensitive out of the box. Even with software updates, fine-tuning each setting ensures peak performance and tailored ride feel.

Understanding the E Ride Pro App Settings

Open your smartphone and launch the E Ride Pro app to access throttle, power, and torque configurations. Understanding each parameter allows you to create a ride that matches your style and terrain—whether technical trails, fast straights, or rough terrain.

Key App Parameters

• Throttle Sensitivity: Adjust this to soften or sharpen throttle response.
• Power Curve: Customize power delivery—reduce aggression for off-road finesse or maximize peak output for full-throttle sprints.
• Torque Control: Smoother initial rollout can enhance traction and reduce wheelspin.
• Motor Cutoff Speed: Safeguard against overspeed by setting a firm limit.
• Regenerative Braking: Increase energy recovery while braking—ideal for maximizing battery life.

Quick Tune Recommendations

1. Start Soft: Reduce throttle sensitivity by 10–20%—gives a smoother initial ride and more predictable power delivery.
2. Power Delivery Curve: Use a moderate ramp-up—good for mixed terrain where steady traction matters.
3. Balance Torque: Adjust initial torque levels to avoid too abrupt launches.
4. Max Speed Check: Confirm your top speed limit is set according to local regulations and rider comfort.
5. Enable Regen: Boost efficiency by turning on regeneration—especially helpful when decelerating.

Tips for Personalized Tuning

• Test, Adjust, Repeat: Ride in controlled environments like parking lots or trails to observe how settings feel.
• Save Your Profiles: If the app supports it, create presets such as “Trail,” “Playful,” or “Range Saver.”
• Review Software Updates: Keep the app and controller firmware updated—they can improve ride feel and unlock new settings.

Why This Matters

Proper tuning decisively enhances ride control, battery efficiency, and overall enjoyment. Tailored throttle behavior can prevent slips, smooth technical maneuvers, and translate into safer, more confident riding.

Full E Ride Pro SR App Guide:

State of System: This screen provides valuable information such as Controller and Motor Temperature, and a state of System reading. This will show the condition that the bike is in, in realtime. In abnormal situations it will display corresponding fault information. If the bike malfunctions please check this immediately.

Battery Voltage: The voltage of the battery will be displayed in real time. When the bike fails to start or loses power, please check this value immediately. If it is lower than 60V, It indicates that the battery is completely drained or there is a battery fault. Please check the connection of the power cable and the power switch.

Bluetooth Password: The Initial password is ERP123. If you receive a message stating the password is incorrect, please try to reset multiple times. 

Password Update: To update the password, it must consist of 5 to 8 characters and can only include numbers or English letters. Please remember your password, if you forget contact E Ride Pro by Email at nick.yang@eridepros.com

Tilt Sensor: When the bike is tilted backward beyond 45 degrees the bike will lose power.

Brake Sensor: When braking, the brake sensor will disengage the throttle.

Kickstand Sensor: When the kickstand is in the down position, the throttle will be disengaged. When the kickstand is up or horizontal, the throttle is engaged. 

Motor Temperature Sensor: Monitoring the temperature of the motor. The App or speedometer will display if the motor is overheating. Turn the motor temperature sensor off to keep riding. (Warning, you can overheat and damage your motor if you do this)

Parking Button: Allows the parking button feature to turn on or off.

Thumb Brake: The Thumb switch acts as a brake, stopping the bike completely when pressed. If the switch gets stuck, the throttle won't work.

Convert Thumb brake to Throttle: If the main throttle is broken, this setting lets the thumb lever act as a throttle. once activated the main throttle will lose function. Recommended only if the main throttle has an issue.

Disable thumb switch: Turns off all functions of the hub switch making it inactive. 

Eco Mode Acceleration: The Recommended setting is 10% for Eco mode acceleration. If you want smooth acceleration reduce to your preference. If you want quicker acceleration go push above 10% to your preference.

Sport Mode Acceleration: The Recommended setting is 10% for Eco mode acceleration. If you want smooth acceleration reduce to your preference. If you want quicker acceleration go push above 10% to your preference.

Race Mode Acceleration: The recommended setting is 8% If you ride on the street or trail, setup to 6% or 7%. If you ride on the track or over technical terrain set up to 9% or more depending on preference.

Thumb Regen Brake: Adjusts electric motor brake strength. The recommended setting is 100%

Reverse Speed Limit: Adjusts the bikes reverse strength. The recommended setting is 10%

Eco Mode Speed Limit: We Recommend 52% for Eco mode speed limit

Sport Mode Speed Limit: We recommend 73% for sport mode speed limit.

Race Mode Speed Limit: We recommend 100% for race mode speed limit.

Save: To confirm your changes, click "Save"

Save Tune: Create and name your custom tune for future use.

Select tune: Choose from your saved tunes

Factory Reset: Restore factory settings. Through this function you can return to the initial system settings, including the settings of sensors and tunes.

The Rename1 and Rename2 are customized tunes that you have saved. Rename it.

Unlock Power: Initial Power is 21KW. Use this button to unlock the full 25KW. Warning: Before you unlock, make sure to wear full protective gear. Please consider this carefully for your safety. E Ride Pro is not liable for any damages or other negative consequences of power. To accept Press Accept to cancel press cancel.

Motor - Controller Sync: To sync motor and controller, place the bike on a work stand and make sure the rear wheel is off the ground. Sync motor and controller after a motor or controller has been repaired or replaced.